Testing Allulose Solubility in Your Beverage Process
Release time:
Nov 16,2026
Author:
Zhongda
Source:
Zhongda
Allulose is highly soluble in water. A laboratory study of equilibrium solubility reported 291 g of D-allulose per 100 g of water at 25 °C, equivalent to about 74.4% by mass in that two-component solution. In a beverage plant, the useful measure is how much dissolves within the available mixing time and what happens when the drink cools. A jar that clears after a long warm stir may tell you little about a cold-water batch waiting to move to the filler. Fukada et al., solubility of D-psicose
Zhongda Hengyuan supplies Sweetism™ D-allulose as powder, granules and syrup, with formulation support for sugar reduction and clean-label projects. This gives developers a choice between dry addition, liquid metering and a custom sweetening blend. The trial should begin with the coldest water and smallest first water charge used at your plant, then follow the complete recipe through its normal hold, heating and cooling cycle. Zhongda's D-allulose forms and beverage applications

Figure 1. Beverage application illustration from Zhongda Hengyuan.
Calculate the concentration at the point of addition
The concentration at addition follows the operator's sequence. If all the sweetener goes into a small first charge of water, the mixer handles a much more concentrated liquid than the finished beverage label might suggest. A useful batch record includes that first water charge, any solids already present, the ingredient mass and the final batch mass. Plenty of water in the finished recipe can still leave very little available when the powder enters the tank.
Take an illustrative 10.00 kg bench batch with 0.30 kg of an offered dry ingredient. The addition rate is 3.0% by mass in the finished batch. If the ingredient is first charged into 0.60 kg of plain water, it is 33.3% of that first mix by mass, calculated as 0.30 ÷ (0.30 + 0.60). Bring 0.30 kg of the same recipe water forward and that figure falls to 25.0%, while the final ingredient addition remains 3.0%. These numbers describe as-weighed ingredient mass for a hypothetical batch. The actual allulose fraction depends on its composition. Use your own water split and record all other solids present at the time of charging.
If the tank needs that water later to disperse another ingredient, keep the original split and test a slower feed or a separate premix. Your plant may have only one workable sequence. In that case, compare allulose forms using that sequence before asking the operator to change it.
Run a water screen and a full recipe
The sample label, technical data sheet, COA and trial sheet should identify the same grade and lot. That link is needed if the bench result will support a commercial order. A water screen makes wetting and dissolution easier to observe, especially when the finished recipe contains haze, pulp or protein.
| Trial | How to run it | What to write down |
|---|---|---|
| Water screen | Charge the identified dry grade into your actual process water at the concentration used in the first mixing stage. Run at normal and lowest expected water temperatures. Keep the vessel, fill level, feed and mixer setup fixed when comparing temperature. | Actual start and end temperatures, first and last powder addition times, wetting or clumping, time to the agreed visible endpoint and any residue. |
| Plant sequence | Repeat the first mix at the smallest planned fill. Test the current feed against one feasible change if wetting is slow. Examples include spreading the charge over a longer interval or making a separate premix. | Mixer and impeller, speed, recirculation where used, batch size, feed rate and residue at the end of the available mixing window. |
| Finished beverage | Use the selected setup with the full recipe. Prepare the current beverage or agreed reference under comparable conditions. Sample after mixing, after the normal process hold and again once cooled to the intended temperature. | Batch weights and addition order, pH, actual heat and hold times, appearance, any sediment and sensory notes versus the reference. |
The available mixing window belongs in the trial brief. An extra five minutes on the bench may be trivial, yet on a line it can delay transfer to the filler. If warmer water is practical, one additional test at a feasible higher temperature can show whether that change helps. Feed conditions should stay the same. For a clear drink, compare samples at the same temperature and viewing conditions once bubbles settle, using the plant's turbidity criterion where available. An opaque drink may be better assessed by a defined screen check for unexpected retained material, with the same screen and sample volume used for the reference.
A stable refractometer reading can help track repeatability within one recipe when the sampling method and temperature are controlled. On a standard sucrose scale, apparent °Brix responds to refractive index, which several dissolved ingredients can affect. If you need to determine allulose content or identify a suspect residue, agree on an analytical method that fits the matrix. OIML guidance on refractometers and sucrose scales
Follow the batch through the hold and cooling step
Where the first signs appear tells you which test to run next. Lumps at the surface during charging point to a wetting or feed problem worth checking at the same concentration and temperature. Particles left in the first mix call for a comparison at the same feed rate with a practical change in water charge or mixing time. Keep each change small enough to tell what helped.
If the first mix clears and haze appears only after you add acid, juice, flavor or protein, take samples before and after the suspect addition. Compare them with a water screen held through the same temperature change and with the finished recipe reference. That helps separate possible crystal formation from a change in the beverage matrix. For concentrate, inspect the cooled sample and the liquid at the lowest expected transfer temperature. Record the actual hold duration and check for settled material after the longest realistic pause.
Include color and flavor in a hot process check. Moon and Han found that extended elevated-temperature storage changed the color and composition of the industrial allulose syrup they studied. Their work concerned a concentrated syrup and storage over weeks. Evaluate the quality of your own formula through its established heat and cooling cycle, and keep that review separate from process safety validation. Moon and Han, allulose syrup storage study
Choose the form you can run at scale
A dry grade makes sense if you can weigh and feed it consistently and complete dissolution inside the available mixing time. If dry addition is the bottleneck and your line can meter liquid, test syrup at the same mass of allulose. Use its as-received assay to set the weight. If the assay is on a dry basis, multiply that fraction by the syrup's solids fraction by mass. Account for its water and other solids before adjusting the batch sheet. For a custom blend with monk fruit or stevia, assess the whole sweetening system against the target ingredient list, flavor and appearance.
Zhongda has a National Enterprise Technology Center and a dedicated automated allulose line designed for 24-hour continuous operation. Our team can discuss formulation alongside the form, composition and specification to be supplied for the pilot. These details need to be settled together when the project moves beyond a bench sample. Zhongda's manufacturing capabilities · National Enterprise Technology Center recognition, entry 54
For U.S. projects, FDA issued a no-questions response to Zhongda's GRAS notice GRN 001309 for the D-psicose and conditions of use described in the notice. The proposed grade, beverage category and use level still need review for the destination market. FDA response to GRN 001309

Figure 2. Exterior of the Zhongda Hengyuan D-allulose production facility, from company materials.
For a sample discussion, send the first water charge and its coldest temperature alongside the batch sheet and available mixing time. A photograph of residue is more helpful when it comes with the time and process step at which it appeared. Zhongda's team can use that brief to discuss the form and specification for your next trial. Request an allulose sample from Zhongda
For teams planning the wider qualification, see how to plan an allulose sample trial before bulk purchase.
Recommend News




